Canola
Technical
Insight 403

DON'T GAUGE THE QUALITY OF A BACTERIAL INOCULANT BY JUST ITS POPULATION COUNT

Back to Technical Insights

 

READING BACTERIAL COUNTS ON BACTERIAL INOCULANT PRODUCT LABELS

Bacterial populations are enumerated by colony forming units or what’s more typically shown on product labels as CFU. Basically the term describes the number of bacterial colonies a microbiologist counts on a pre-defined area on a culture plate as shown in the image at the right.

CFU population counts usually are reported on a per gram basis (CFU/g). Be sure to compare “apples to apples” when comparing labelled CFU counts of various products.

UNDERSTANDING LOGARITHMS USED IN BACTERIAL INOCULANT PRODUCT LABELS

The use of logarithms provides microbiologists with a method to easily indicate CFU/g or CFU/lb without having to write out the number in typical numerical form. Logarithms (logs) work on a base 10 method so that the number 10 = log 1, 100 = log 2, 1,000 = log 3, etc. Logs are written in the following fashion: 10n; for example a log 3 would be 103.  An absolute number is found in front of the log number. For example 3,000,000,000 CFU/g would be expressed as 3.0 X 109 where the absolute number is “3” and the log is that number of “0s” to the right of the decimal point. The label on Pioneer 1132 inoculant reads 1.25 X 1011 CFU/g product, which is the same as 125,000,000,000.  

CLASSICAL BACTERIAL GROWTH CURVE DURING THE ENSILING PROCESS

Bacteria follow a similar logarithmic growth pattern during the ensiling process as shown by the Classical Bacterial Growth Rate Curve illustration. Bacterial growth starts out with minimal activity, followed by a fast logarithmic growth phase. The curve exponentially plateaus out into a stationary phase due to the bacteria creating its low pH environment. Bacteria CFU counts then start to decline over time, some bacterial growth declines occur faster than others.  

How fast bacterial CFU populations multiply is dependant on several variables such as type of crop, substrate, temperature and silage management practices. For instance, a Lactobacillus plantarum strain could require three to seven days in silage to move from “lag phase” to “stationary phase”. This is dependant not only on the variables listed above but also the particular strain. The CFU/g forage log value for a Pioneer.

BACTERIAL INOCULANT APPLICATION GOAL: 100,000 CFU/g Forage and 10,000 CFU/g HMC (High Moisture Corn)

Early silage inoculant research from Europe determined that a bacterial inoculant should be applied at a level to achieve 100,000 (105) CFU/g forage and is the application dosage for all forages treated with Pioneer’s bacterial strains. Forage Additive researchers discovered, prior to the introduction of 1186, that less than optimal fermentation performance resulted when HMC was applied at the 100,000 CFU/g rate for HMC. After researching various dosage levels, the researchers determined that applying Pioneer’s bacterial strains at 10,000 CFU/g was more effective for HMC. The packaging of the various crop specific inoculant products from Pioneer has different guaranteed CFU/g counts. You can be assured that Pioneer has formulated products at these levels to insure the delivery of the optimum dosage to your forage.

Competing companies may claim their product is superior because their product results in 400,000 CFU/g forage while Pioneer’s is only at 100,000. The misleading part of this statement is that drastic differences exist in the ability of bacterial strains to DOMINATE fermentation. Bacterial strains in the silo will multiply until they achieve a CFU/g population of 1 billion and seldom exceed that population count. Pioneer Forage Additive researchers perform thousands of repetitive experiments to discover which Pioneer bacterial strains are able to DOMINATE fermentation and at what dosage level they most effectively can DOMINATE fermentation. Scott Dennis, Director of Quality Control in Pioneer’s Forage Additive Research group states: “what the other companies use is irrelevant, it’s what our research has shown to be the most efficacious for Pioneer strains that determines the CFU/g that Pioneer products should be applied to forages and High Moisture Corn (HMC).

DON'T FALL INTO THE CFU COUNT TRAP

Inoculant competitors often sell their product based on CFU/g population counts that greatly exceed what is found in Pioneer® brand inoculant. Those companies selling customers inoculant based on CFU counts usually fail to have background research demonstrating the ability of the product to:

  1. Promote efficient fermentation and decrease shrink
  1. Enhance digestion, protein quality and feeding efficiencies for improved dairy and beef performance, and
  1. Improve bunk-life properties at feed-out. 

The research behind the unique and patented combinations of Pioneer’s bacterial strains used to develop Pioneer’s crop specific inoculant products are what determine the value of Pioneer® brand inoculants.


Pioneer® brand products are provided subject to the terms and conditions of purchasing, which are part of the labeling and purchase documents.

®, SM, Trademarks and service marks of Pioneer Hi-Bred International, Inc.

The information on this website is general in nature only. Although the information in this website is believed to be accurate, no liability (whether as a result of negligence or otherwise) is accepted for any loss of any kind that may arise from actions based on the contents of this publication.

© 2017, GenTech Seeds Pty Ltd. No part of this publication can be reproduced without prior written consent from GenTech Seeds Pty Ltd.

Revised: March 2017
Expires: March 2018